Review of H11 Led 2018 Headlights From Aliexpress

Are You lot Tired The Poor Light Output From Your Stock Halogen Bulbs? XenonDepot Has The Respond For You!

The XenonDepot LED H11 replacement for the 3rd Gen Toyota Tacoma is a great upgrade.

I of the get-go modifications I did with my truck was to supersede the OEM Element of group vii bulbs that come stock with the Tacoma. The initial light output from the factory is dismal at best, it did the job, merely I knew at that place was something amend out there!

Budget LEDs VS XenonDepot

I went the cheaper route and ordered some from Amazon in the $35-$65 dollar toll range the start time I decided to upgrade my low-beams.

The aftermarket Amazon LEDs were fine but they didn't make the road any more visible than my stock bulbs. The lights were a little scrap brighter but the bodily reach (lux) of the lite was very short.

Lux VS Lumens is a whole other topic that you lot may desire to research before buying aftermarket lights. After having good luck with my XenonDepot XTR Reverse Lights, I decided to pull the trigger on these XenonDepot LED Pros to replace my low beams. After driving around at dark for the first couple of days and bringing it out on the highway, the difference was extremely noticeable.

HID or LED?

At that place are currently 3 main technologies in the vehicle lighting earth:

1. HID (High-Intensity Discharge)
2. LED (Light Emitting Diode)
3. Halogen

Halogen blazon bulbs have been around since the modernistic car was invented so followed by HID, then most recently LED lights. HIDs were the popular choice when they first came onto the scene, simply with the recent developments in technology and improvements to LED products, LEDs have become the front runner in vehicle lighting.

The LED Advantage

Energy Efficient

• LED lights are more energy-efficient than their halogen and HID counterparts. They have greater light output but draws fewer amps from your electrical system.

Instant Light

• Different HIDs, which take a second to warm up, LEDs plough on right away. If you have a current changer in your vehicle some vehicles are even able to dim the brightness of the LED, for case, if you lot were stuck in traffic.

Reduced Glare

• Different HIDs, LEDs are a bright concentrated calorie-free source, then you exercise not have to worry most distracting glare with oncoming traffic.

Reduced Rut Output

• LEDs also stay much cooler than Halogen and HID.

Increased Lifespan

• The longevity of LED lights greatly surpass both Halogen and HID. Some manufacturers have stated up to 50,000-hour life span on their LED lights.

Why Xenon Depot? Are They The Best?

I firmly believe that Xenon Depot along with a few other companies (Headlight Revolution, Morimoto, Etc.) make the absolute highest quality headlight bulbs in the manufacture. Every bit shortly as you accept it out of the box, you can tell that this is an splendid production. It's most twice the price of the median Amazon LED light, but well worth the money.

These lights have the all-time output, concentration, and colour gradient compared to Amazon or eBay alternatives.

Detect Them Online

• Xenon Depot H11 Xtreme LED PRO Bulbs: Check Price

Let's get these bad boys installed.

Step 1. Get Admission To Your Headlights

Information technology is not necessary to remove the grill from the Tacoma, just information technology does give you more than working room around both the headlight housings. The grill on the Tacoma is simply held in place with 2 screws and two clips. It is very easy to remove.

Use a Phillips screwdriver head to remove both screws. Then, if you have an automotive prune remover, utilize that to remove the clips on both sides. If y'all do non have ane, a screwdriver tin work just equally well to pop them off.

Stride 2. Remove Headlight Seedling

Permit's outset with the commuter'due south side headlight.

Due to the battery, admission to the driver's side bulb is slightly more hard. You will still be able to access the seedling, simply if y'all want to remove your battery, information technology tin brand the chore a bit easier. The headlight bulb is the second from the right if you are looking from the motorcar from the front end. Achieve behind and twist left to remove the calorie-free from the housing. Be sure the depression beam connector/harness is unlocked from the headlight earlier removing.

As you tin see from the photo above, my old Amazon LED calorie-free is being compared to the erstwhile XenonDepot. The Amazon LED has one Cree bit on each side while the XenonDepot has 3.

Step 3. Connect Harness

The LED Pro Low Beams come with a harness to connect to the OEM H11 plug; you'll want to connect this harness to that plug.

Follow the steps below to connect the XenonDepot provided Harness.

Connect 2-Prong Male + Female Ends

Connect the two-prong male person and female person ends.

Annotation: The polarities may be reversed so double-check both sides then that the positive and negatives are lined upwards correctly.

Connect Smaller 4-Prong Connections

At present connect the smaller 4 prong connections and screw on the weather condition seal cap.

Reconnect OEM H11 Plug To Xenon Depot Plug

You will end up with the harness and a XenonDepot low beam that looks like this. At present all that is left to do is to reconnect the OEM H11 plug to the provided Xenon Depot One.

Pace 4 – Connect Harness To OEM H11 Connector

Step 5. Test The New Bulbs

Turn on your lights to make sure the LED bulbs work.

If they don't plough on the beginning fourth dimension, the polarity on the connectors may be reversed; check the associates again and the light turn should turn on if it didn't the first time.

Footstep 6. Fan Out Heatsink

Fan out the heatsink when yous put the low axle back in the headlight housing.

Make certain that the adjustable heat sink is non touching any wires. It'southward not a huge deal if it does, but better to have it free of anything, y'all don't want the heatsink to wear through the protective roofing and betrayal a alive wire.

Step 7. Neatly Tuck Away Excess Wires

I used zero ties to tuck the harness and the wires away in the space between the primary engine bay and the fenders. The in a higher place epitome is of the passenger side.

Footstep 8. Reinstall Your New Seedling Into The Housing

Simply as you removed your manufactory bulb, only reinstall the new XB LED back into place, and you're done.

Initial Thoughts for Xenon Depot LED Pro

As soon as I put these in the truck I could immediately meet a big difference. The light output is super concentrated and the lite is very vivid. The bodily distance (lux) the beam threw was extremely far.

The light output of XenonDepot is amazing! They put out brilliant white light, unlike other competitors which are closer to the blue portion of the Kelvin calibration. The distribution pattern of the lights will depend on the type of lens/headlight you're running.

Concluding Thoughts

I would recommend these lights to anyone looking for a lighting upgrade. They are great out on the trail and for daily driven trucks. They will give you greater visibility on the road and you tin see cars and/or obstacles much sooner. Kudos to XenonDepot for putting out another quality product!

sawyersatho1977.blogspot.com

Source: https://trailtacoma.com/2020/04/27/xenon-depot-h11-xtreme-led-pro-low-beam-install-review-3rd-gen-tacoma/

Share this post